To connect a mobile phone to a hot spot, you typically open Wi-Fi settings app, list available networks and then pick the hot spot you need. You can also list the networks with ESP8266 and here is how.
This example shows the bare minimum code we need to check for the list of available networks.
Disconnect¶
To start with, enable module in station mode and then disconnect.
Wi-Fi Scanner (WiFi Scanner.exe). Wi-Fi Scanner allows you to easily locate visible wireless networks and corresponding information. The tool obtains the network name (SSID), signal strength (RSSI) and quality, MAC address (BSSID), channel, maximum and achievable data rate, security, and much more. Acrylic Wi-Fi Home – WiFi Scanner. Acrylic WiFi Home allows you to perform network analysis.
Running
WiFi.disconnect()
is to shut down a connection to an access point that module may have automatically made using previously saved credentials.Scan for Networks¶
After some delay to let the module disconnect, go to scanning for available networks:
Now just check if returned
n
if greater than 0 and list found networks:This is that simple.
Complete Example¶
The sketch should have obligatory
#include<ESP8266WiFi.h>
and looks as follows:Example in Action¶
Upload this sketch to ESP module and open a serial monitor. Diluvion 1 17. If there are access points around (sure there are) you will see a similar list repeatedly printed out:
When looking for the text
scanstart..
displayed, you will notice that it takes noticeable time for the following text nnetwork(s)found
to show up. This is because execution of WiFi.scanNetworks()
takes time and our program is waiting for it to complete before moving to the next line of code. What if at the same time we would like ESP to run time critical process (e.g. animation)that should not be disturbed?It turns out that this is fairly easy to do by scanning networks in async mode.
Check it out in next example below that will also demonstrate printing out other parameters of available networks besides SSID.
What we like to do, is to trigger process of scanning for networks and then return to executing code inside the
loop()
. Once scanning is complete, at a convenient time, we will check the list of networks. The “time critical process” will be simulated by a blinking LED at 250ms period. Photosblender linear or square image blending 1 1 2.We would like the blinking pattern not be disturbed at any time.
No delay()¶
Wifi Scanner 2 7 4 X 4
To implement such functionality we should refrain from using any
delay()
inside the loop()
. Instead we will define period when to trigger particular action. Then inside loop()
we will check millis()
(internal clock that counts milliseconds) and fire the action if the period expires.Please check how this is done in BlinkWithoutDelay.ino example sketch. Identical technique can be used to periodically trigger scanning for Wi-Fi networks.
Setup¶
First we should define scanning period and internal variable
lastScanMillis
that will hold time when the last scan has been made.When to Start¶
Then inside the
loop()
we will check if SCAN_PERIOD
expired, so it is time to fire next scan:Please note that
WiFi.scanNetworks(true)
has an extra parameter true
that was not present in previous example above. This is an instruction to scan in asynchronous mode, i.e. trigger scanning process, do not wait for result (processing will be done in background) and move to the next line of code. We need to use asynchronous mode otherwise 250ms LED blinking pattern would be disturbed as scanning takes longer than 250ms.![Wifi scanner 2 7 4 download Wifi scanner 2 7 4 download](https://www.usa.canon.com/internet/wcm/connect/us/37002bc1-6c42-4e96-8aa4-03d7b901cd24/pixma-mg5520-wireless-inkjet-photo-aio-printer-black-front-d.jpg?MOD=AJPERES&CACHEID=ROOTWORKSPACE.Z18_P1KGHJ01L85180AUEPQQJ53034-37002bc1-6c42-4e96-8aa4-03d7b901cd24-kZnWWc-)
Check When Done¶
Finally we should periodically check for scan completion to print out the result once ready. To do so, we will use function
WiFi.scanComplete()
, that upon completion returns the number of found networks. If scanning is still in progress it returns -1. If scanning has not been triggered yet, it would return -2.Please note function
WiFi.scanDelete()
that is deleting scanning result from memory, so it is not printed out over and over again on each loop()
run.Wifi Scanner 2 7 4 Iso
Complete Example¶
Complete sketch is below. The code inside
setup()
is the same as described in previous example except for an additional pinMode()
to configure the output pin for LED.Example in Action¶
Upload above sketch to ESP module and open a serial monitor. You should see similar list printed out every 5 seconds:
Check the LED. It should be blinking undisturbed four times per second.
The scan class API provides comprehensive set of methods to do scanning in both synchronous as well as in asynchronous mode. Therefore we can easy implement code that is doing scanning in background without disturbing other processes running on ESP8266 module.
For the list of functions provided to manage scan mode please refer to the Scan Class documentation.
Easy-to-use tool to scan for and analyze 802.11a/b/g/n/ac wireless networks Cross dj 3 4 3 – professional dj software.
Wi-Fi Scanner allows you to easily locate visible wireless networks and its corresponding information. The tool obtains the network name (SSID), signal strength (RSSI) and quality, MAC address (BSSID), channel, maximum and achievable data rate, security, and much more.
Wi-Fi Scanner is useful for normal access point users who need to find out the signal strength distribution for their wireless network at home, or choose a position for their access point for optimal signal quality.
Using Wi-Fi Scanner, you can evaluate the allocation of wireless networks by channel and select the least congested bandwidth for their access point, allowing them to increase their connection speed significantly.
In addition, Wi-Fi Scanner is an indispensable tool for corporate network administrators in performing tasks such as configuration, planning and monitoring security parameters on business wireless networks.
Key features
- Simple, fast wireless network search
- Support for 802.11ac and 802.11a/b/g/n
- Support for 2.4 and 5 GHz frequency bands
- Support for 20, 40, 80, 160 and 80+80 MHz channel widths
- Display detailed information for wireless network: network name (SSID), signal level (RSSI), MAC address (BSSID), signal quality, channel, achievable and maximum data rate, encryption, channel utilization, clients etc.
- Show detailed description of information elements (IE)
- Detect security standards WEP, WPA or WPA2 for wireless networks
- Support for WPS 1.0 and WPS 2.0
- Device name and model number discovery of access points
- Display changes in signal level over time in graphical form
- Display signal spectrum mask for each wireless network
- Customizable graph color for any wireless network
- Filter list of detected wireless networks by specified parameters (quality, network mode, security, etc.)
- Connect to detected networks
- Display Wi-Fi radio state (software, hardware)
- Display wireless connection parameters
- Display wireless connection statistics in the form of graphs and tables
- Manage wireless connection profiles
- Disconnect/connect wireless adapters
Scanner With Wifi
Getting started with Wi-Fi Scanner
Wifi Scanner 2 7 4 Download
The best way to get started with Wi-Fi Scanner is to try it, no strings attached. We are so confident that you will have a great user experience with our software that we offer Wi-Fi Scanner in a fully-functional trial package. Click here to download your fully-functional trial of Wi-Fi Scanner . The Wi-Fi Scanner is free for personal use. Need for business use? LizardSsystems Software has a simple pricing. Please visit our pricing page for further information.